AX1800 Dual Band WiFi 6
Two (2) internal dual-band antennas
IEEE 802.11 a/b/g/n/ac/ax, 2x2 MU-MIMO
WiFi 6 Performance (OFDMA, Beamforming, Power Boost, 1024-QAM)
Transmit power: up to 30 dBm
Smart Mesh 2.0
Up to 574 Mbps** at 2.4 GHz
Up to 1,200 Mbps** at 5.0 GHz
Coverage up to 5,000 sqft.*
Guest network support
Seamless AP Roaming
Wireless Airtime Fairness (ATF)
Optimized WiFi Channel Selection
WPA2 AES wireless security
64 client devices per WiFi band; up to 245 total client devices
Firewall with DoS Attack Protection, SPI
One (1) 10/100/1000 Gig Ethernet LAN port
One (1) 10/100/1000 Gig Ethernet WAN port
Two (2) 10/100/1000 Gig Ethernet LAN ports
USB-C Power Input Port
Front Status LED: Power, WiFi, Internet
Dimensions: 2.6" H x 5" D x 5" W
Weight: 10.6 oz
Ruggedized 4 kV surge protection
FCC part 15B, 15C, and 15E, FCC MPE, UL 62368 and NRTL safety mark, RoHS, California Prop 65
*WiFi coverage range is derived from testing under ideal conditions. Actual WiFi coverage may be lower due to environmental factors and client limitations.
** Maximum WiFi transmission rates are the physical rates derived from the 802.11 specifications. The actual WiFi transmission rate will be lower due to environmental factors, network conditions, and client limitations.
MTRLC LLC warrants this product against defects in material and workmanship for a warranty period of 2 years. To read the full warranty, please visit: www.motorolanetwork.com/warranty
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All safety guidelines of this device and of any connected equipment must be followed to ensure safe use.
These precautions help protect you and your Mesh device (Q11).
- Devices are intended to be placed indoors in an environment that’s between 32° and 104° F (0-40°C)
- Avoid water and spills
- Leave room for airflow around the device, do not block the vents on the rear or bottom
- Marking information is located on the bottom of the product
- The power adapter plug is used as the disconnect device. The connected AC power outlet must be located near the equipment and be easily accessible
i. MINIM INC. AND MTRLC LLC ARE NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS TO THE EQUIPMENT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
ii. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
a. Reorient or relocate the receiving antenna.
b. Increase the separation between the equipment and receiver.
c. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
d. Consult the dealer or an experienced radio/TV technician for help.
iii. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.
iv. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
v. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
vi. RF Exposure Statement: This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons, and must not be co-located or operating in conjunction with any other antenna or transmitter.
©MTRLC LLC 2021. MOTOROLA and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. and are used under license. All other trademarks are the property of their respective owners. All rights reserved.